REGISTERED No. D. 221 रजिस्ट्री सं ० डो० 221
भारत का राजपत्र The Gazette of India
श्रसाधारण
EXTRAORDINARY
भाग II- खण्ड 3 -- उपखण्ड ( ii ) PART II- Section 3-Sub - section ( ii )
प्राधिकार से प्रकाशित
PUBLISHED BY AUTHORITY
सं०453]
नई दिल्ली , बुधवार , सितम्बर 20 , 1967 /মায় 29 , 1889
No.453) NEW DELHI , WEDNESDAY, SEPTEMBER 20 , 1967 / BHADRA 29 , 1889
इस भाग में भिन्न पृष्ठ संख्या ही जाती है जिससे कि यह अलग संकलन के रूप में रखा जा सके ।
Separate paging is given to this Part in order that it may be filed as a separate compilation .
MINISTRY OF COMMERCE
NOTIFICATIONS
New Delhi , the 20th September 1967
S.O. 3411.-In3411. In exercise of the powers conferred by section 6 of the Export (Quality Control and Inspection ) Act , 1963 ( 22 of 1963 ) , and after previous pub- lication as required by sub - rule ( 2 ) of rule 11 of the Export ( Quality Control and Inspection ) Rules , 1964 , the Central Government hereby-
(1) notifies that small tools and hand tools shall be subject to quality control and inspection prior to export;
( 2) specifies the type of quality control and inspection in accordance with the Export of Small toolsols and Hand tools ( Quality Control and Inspection ) Rules , 1967 as the type of quality control and inspection which would be applied to such small tools and hand tools;
(3) recognises-
(a) the contractual specifications as agreed upon between the buyer and the seller; and
(b) in the absence of any contractual specifications as mentioned in clause ( a) above , the specifications issued by the Indian Stand- ards Institution for small tools and hand tools as set out in An- nexure I to this Notification .
as the standard specifications for small tools and hand tools ;
(4) prohibits the export , in the course of international trade, of such small tools, and hand tools unless the same are either accompanied by a
(1565) THE GAZETTE OF INDIA EXTRAORDINARY
1566
[PART II-
certificate issued by any of the Export Inspection Agencies estab- lished under section 7 of the Export ( Quality Control and Inspec- tion) Act , 1963 ( 22 of 1963 ) , to the effect that the small tools and hand tools are export - worthy , or are affixed with a seal or mark recognised by the Central Government under section 8 of the said act.
2. Nothing in this Notification shall apply to the export by land, sea or air of samples of small tools and hand tools not exceeding twelve in number of each type and size to prospective buyers.
3. Definition--In this Notification , ' Small tools , shall mean any of the small tools used by machinists , while doing machining work , and 'Hand tools' shall mean any of the hand tools used by fitters or carpenters or others doing hand work .
This Notification shall come into force on 13th of October , 1967
ANNEXURE I
List of Indian Standards
[See clause (b) of sub - para ( 3 ) of para 1 ] .
Sl. Commodity Relevant specifica-
No. tion issued by Indian
Standards Institution
(1) (2) (3)
X Adzes IS : 663-1964
2 Axes IS: 703-1966
3 Blacksmith's Anvil (Cast steel ) IS: 510-1964
4 Bench Vics Machinist's Vices IS : 2586-1964
5 Blacksmith's Vices IS : 2588-1964
6 Carbide Tipped Single Point Turning Tools IS: 2163-1963
7 Carpenters Augers IS: 2852-1964
8 Centre Drills IS : 664-1963
9 Chisels IS : 402-1964
10 Crow Bars and Claw Bars IS : 704-1957
II Engineer's files IS: 1931-1962
12 General requirements for Milling Cutters IS: 1830-1961
13 Hand Hammers IS: 841-1957
14 Hacksaw Blades IS: 2594-1963
15 Interlocked Milling Cutters IS: 2671-1964
16 Milling Cutters for Woodruff key slots IS : 2669-1964
17 Pipe Vices ( open side type fixed size type) IS : 2587-1964
18 Picks and Beaters IS : 273-1961
19 Pilers , pincers and nippers general requirements for IS: 2615-1964
20 Powrahs IS : 1759-1961
21 Punches , Round IS : 413-1965
32 Reamers IS: 1836-1961
23 Reduction Sleeves and Extension Sockets for Morse Tapers IS : 2608-1964
24 Ring Spanners IS: 2029-1962
25 Screw Drivers IS: 844-1962
26 Shovels IS: 274-1961
27 Smith Bits IS : 552-1965
28 Smith's Flatters IS: 846-1956
29 Smith's Fullers IS: 847-1956
30 Smith's Swages IS: 842-1956
31 Smith's Tongs IS : 843-1956
32 Spanner , Box IS: 2030-1962
33 Spanner , Open Jaw IS : 2028-1962
34 Swage Blocks and Stands IS: 845-1961
35 Screwing Taps IS: 1988-1962
36 T- Slot Milling Cutters IS: 2668-1964
37 Threading Cutting Dies .IS: 1859-1961
THE GAZETTE OF INDIA EXTRAORDINARY
S8( 11 )
(1)
(2)
38 Thread Milling Cutters ( Shell Type) 39 Truing Tools Single Diamond
40 Twist Drill
41 Wood Working Chisels andGauges 42 Width Across Flats for Spanners
43 Keys for Lathe Chucks
44 Hexagonal Keys for socket head screws 45 Needle Files
46 Eyelet Pliers
47 RoundNose Pliers .
48 Flat NosePliers
49 Burner Pliers
50 Rasps
51 Dimensions for Self- Holding Tapers 52 Dimensions for Milling Cutters
1567
(3
IS : 2670-1964 IS : 2794-196.1 IS : 599-1960 IS : 193-1961 IS : 2027-1962 IS : 2989-1965 IS : 3082-1965 IS : 3152-1965 IS: 3529-1966 IS : 3568-1966 IS : 3552-1966 IS : 3569-1960 IS : 3587-1966 IS : 1715-1963 IS : 1831-1961 53 Dimensions for Shank Diameters and Driving Square for Rotating
Tools
IS : 1850-1
IS : 1983-1962 54 Shank Sections for Single Point Turning and Planing Tools .
IS : 2162-1962 55 Dimensions for Carbide Tips for Single Point Turning Tools
56 Milling Arbors
57 Accessories for Milling Arbors
58 Plug and Ring Gauges for Self- Holding Tapers IS : 2169-1963 IS : 2170-1963 IS : 2251-1965 59 Dimensions for Self- Release ( 7/24 ) Tapers for Arbors and Spindle Noses for Milling Machines
IS : 2340-1964 60 Application for Carbides for Machining Ranges of Application and colour Code
IS : 2428-1964 61 High Speed Steel and Carbon Tool Steel Single Point Turning
Tools
62 Recommendations for Tappnig Drill sizes 13 Die Holder for Circular Thread Cutting Dies .
IS . 3019-1965 15 : 3230-1965 IS : 3239-1940
NOTE : If in respect of any commodity specified in column ( 2) there are any later vers ons to the relevant specifications by the Indian Standard Institute , the specification applicable tosuch commodity shall be the latest of such versions and not the specification mentioned in column (3)
[No. 60 ( 21 ) Exp . Insp/ 67 . ]
S.O. 3412.-In exercise of the powers conferred by section 17 of the Export (Quality Control and Inspection ) Act , 1963 (22 of 1963 ) , the Central Government hereby makes the following rules , namely:-
1. Short title and commencement .---( 1 ) These rules may be called the Export of Small Tools and Hand Tools ( Quality Control and Inspection ) Rules , 1967 .
( 2 ) They shall come into force on 13th October , 1967 .
2. Definition. In these rules , unless the context otherwise requires-
( a) ' Agency' means any one of the Export Inspection Agencies established at Cochin , Madras , Calcutta , Bombay and Delhi under section 7 of the Export ( Quality Control and Inspection ) Act . 1963 ( 22 of 1963 ) .
(b ) ' Small tools' shall mean any of the small tools used by machinists . while doing machining work and 'hand tools ' shall mean any of the hand tools used by fitters or carpenters or others doing hand work .
3. Quality Control .- ( 1 ) The quality of the small tools and hand tools mtended for export shall be ensured by effecting the following controls , at different stages of manufacture together with the levels of control as given in Annexure hereto namely:-
( 1 ) Bought out materials and components control :
(a) Purchase specifications shall be laid down by the manufacturer in- corporating the properties of materials or components to be used and the detailed dimensions thereof with tolerances .
THE METTE OF INDIA EXTRAORDINARY
1568
[PART 11-
(b) The accepted consignments shall be either accompanied by a supplier's test or inspection certificate corroborating the requirements of the purchase specification , in which case occasional checks ( e.g. once in each quarter of the year for the same supplier of the same mate- rial) shall be conducted by the purchaser for a particular supplier to verify the corectness of the aforesaid test of inspection certifi- cates , or the purchased materials or components shall be regularly inspected or tested either in a laboratory within the factory or in some other laboratory or test house .
( c ) The sampling for inspection or test to be carried out shall be based on a recorded investigation .
( d ) After the inspection or test is carried out , systematic methods shall be adopted in segregating the accepted and rejected materials or com- ponents and in disposal of rejected materials or components .
( e ) Adequate records in respect of the above mentioned controls shall be regularly and systematically maintained .
( ii ) Process Control :
( a ) Detailed process specifications shall be laid down by the manufacturer for different processes of manufacture .
( b ) Equipments , instrumentation and facilities shall be adequate to control the processes as laid down in the process specification .
( c) Adequate records shall bt maintained to ensure the possibility of veri- Iying the control , exercised during the process of manufacture .
( iii ) Product Control .
esting ( a) The manufacturer shall either have his own adequate testing facilities . or shall have access to such testing facilities existing elsewhere to test the product as per the specification recognised under section 6 of the Export ( Quality Control and Inspection ) Act , 1963 ( 22 of 1963 ) .
(b ) Sampling ( wherever required ) for testing shall be based on a recorded investigation .
( c ) Adequate records in respect of tests carried out shall be regularly and systematically maintained .
( iv ) Preservation Control:
( a ) A detailed specification shall be laid down by the manufactmer to safeguard the product from adverse effects of weather conditions .
( d ) The product shall be well preserved both during storage and during transit .
(V ) Packing Control :
A packing specification shall be laid down with a view to satisfying the controls mentioned in the Annexure hereto annexed for packing the aforesaid product and shall be rigidly implemented.
( 2) Inspectin . The inspection of small tools and hand tools intended for ex- port shall be carried out with a view to seeing that the above mentioned controls have been exercised at the relevant levels satisfactorily and that the small tools and hand tools conform to the standard specifications applicable to it .
4. Procedure of Inspection ( 1 ) The exporter shall give intimation in writing to any one of the agencies recoginsed under section of the Export ( Quality Control and Inspection ) Act , 1963 ( 22 of 1963 ) , and submit along with such inti- mation a declaration that the consignment of small tools and hand tools have been or are being manufactured by exercising quality control measures as per controls referred to under rule 3 above , and that the consignment conforms to the re- quirements of the specifications recognised for the purpose ,
( 2) The exporter shall also furnish to the Agency the identification marks applied on the consignment .
(3 ) Every intimation and declaration under sub - rule ( 1 ) shall reach the office of the Agency not less than seven days prior to the despatch of the consignment from the manufacturer's premises or exporter's premises .
THE GAZETTE OF INDIA EXTRAORDINARY
SEC. 8 ( 1 ) ]
1569
(4) On receipt of the intimation and declaration under sub - rules ( 1 ) and ( 2 ) , the agency:-
( a) in the case of an exporter who is himself the manufacturer on satis- fying itself that during the process of manuracture he had exercised adequate quality control as provided under rule 3 and the instruc- tions , if any , issued by the Export Inspection Council in this regard to manufacture the product according to the standard specifications applicable to it , shall within three days , issue a certificate declaring the consignment of small tools and hand tools as export- worthy ;
(b ) in the case of an exporter who is not himself the manufacturer on satis fying itself that during the process of manufacture the manufac- turer had exercised adequate quality control as provided under rule 3 and the instructions , if any , issued by the Export Inspection Coun- cil in this regard to manufacture the product according to the stand- ard specifications appheable to it, shall within three days of carry- ing out the inspection , issue a certificate declaring the consignment of small tools and hand tools as export - worthy .
5. Affixation of recognised mark and procedure thereof . The provisions of the Indian Standards Institution ( Certification Marks ) Act, 1952 ( 36 of 1952 ) , the Indian Standards Institution ( Certification Marks ) Rules , 1955 and the Indian Standards Institution ( Certification Marks ) Regulations , 1955 , shall , so far as may be, apply in relation to the procedure of affixation of the recognised mark or seal on small tools and hand tools prior to export and tools so marked shall not be subjected to any inspection under rule 4 of these rules .
6. Place of Inspection .--- Every inspection under these rules shall be carried out at the premises of the manufacturer or cxporter at the port of shipment .
7. Inspection Fee . A fee at the rate of twenty paise for every hundred rupee of f.o.b. value of each such consignment shall Le paid by the exporter to the Agency as inspection fee under rule 4 of these rules .
8. Appeal . ( 1 ) Any person aggrieved by the refusal of the Agency to issue a certificate under sub - rule ( 4 ) of rule 4 may , within ten days of the receipt of the communication of such refusal by him , prefer an appeal to a panel of experts , consisting of not less than three persons , as may be appointed for the purpose by the Central Government
( 2) The quorum for the panel shall be three
( 3 ) The decisions of the said panel of experts on such appeal shall be final .
ANNEXURI
(See rule 3 )
Levels of control
Reference
I otsize Requirement
No. samples to be tested
Sl. No.
2
I
3
5
T Dimensions within tolerances Standard specifica- tions 1c- a) Each
a) Critical (b) Other ,
cognised for the
(b) as perrecorded investigation
purpose
Do.
2 Weight within tolerance
Do. Do.
3 Nos .
3 Hardness
Do.
cach chargefrom ahoven 4 Eccentric ty Test
As per recorded
Do.
investigation Do.
5 Drop Test ( Forged tools )
Do.
Each
6 Check for defe ts
Do.
7 Performance
investigation As per recorde 1
Do. Each .
8 Workmanship
Do.
Do.
9 Finish THE CAZEFIL OF INDIA EXTRAORDINARY
1570
τ
2
To For wooden handles only (a ) Fumoer
5
4
3
Standard spec.fica- 5Nos.
tio is recognised for
specis
the pupose
(b) Moisture content
(c) Treatment
II Packing
* ( a) Appearance
**( n ) Drop Test
(c) Rolling Test
Water Spraying Test Do. 5%
Consignment of same Each shift's produc-
tion.
Do. 10 Nou .
Do.
Do. Each
1No.
Do.
Each consignment
Do.
Do.
Do.
Do. Do.
Each design .
* I'ne package shall bewell finished and havea good appearance .
** The inner contents of the package shall be so packed as to withstand Drop Test , Rolling Test , and Water Spraying Test as given below:
(a) Drop Test ( for wooden cases restricted to head loads only upto weight of 37 kg. )
The package to be dropped from a height of 125 cm once on the largest flat surface , once on the longest edge and once on any corner of its own,
( 1 ) Rolling Test ( for wooden cases only restricted to a weight of 500 kg . ) .
The package to be subjected to rolling on its sides either 6 metres forward and 6 metres backward or 12 metres in one direction only .
( c ) Water Spraying Test. The package to be allowed to be exposed normal sudden monsoon against a water spray equivalent to a shower for five minutes .
(No. 60 ( 21 ) Exp . Insp./67 .)
S.O. 3413. - In exercise of the powers conferred by section 7 of the Export (Quality Control and Inspection ) Act , 1963 ( 22 of 1963 ) , the Central Government hereby recognises the following Inspection Agencies for quality control and inspection of small tools and hand tools for purposes of export , in granting the certificate under sub - rule ( 4 ) of rule 4 of the Export of Smali Tools and Hand 'Tools (Quality Control and Inspection ) Rules , 1967 namely :
1. Export Inspection Agency , Cochin , ' Manohar Building' Mahatama Gandhi Road Ernakulam -1.
2. Export Inspection Agency , Madras , World Trade Centre, Sire Mansion . 123 , Mount Road , Madras - 6 .
3. Export Inspection Agency, Calcutta ' World Trade Centre ' , 14 / 1 -B , Ezra Street ( 10th floor ) , Calcutta -1 .
4. Export Inspection Agency , Bombay , Harchandrai House, Ist floor , 18 een's Road, Bombay-2. Queen'
5. Export Inspection Agency , Delhi , 2179 , Gurudwara Road , Karol Bagh , New Delhi - 5-
Explanation.In this notification " small tools " shall mean any of the small tools used by machinists , while doing machining work , and "hand tools " shall mean any of the hand tools used by fitters or carpenters or others doing hand work.
[No. 60 ( 21 ) Exp . Insp./67.1
S.O. 3414. In exercise of the powers conferred by section 8 of the Export (Quality Control and Inspection ) Act . 1963 ( 22 of 1963 ) , and after previous pul lication as required by sub - rule ( 2) of rule 11 of the Export ( Quality Control and Inspection ) Rules , 1964, the Central Government recognises the Indian Stand- ards Institution Certification Mark with ith respect to small tools and hand tools for the purpose of denoting that where small tools and hand tools are affixed with such mark , they shall be deemed to be in conformity with the standard speci- fication applicable thereto under clause ( c ) of section ở of the said Act.
THE GAZETTE OF INDIA EXTRAORDINARY
SFC. 3 ( li) ]
1571
Definition-In this notification ' small tools ' shall mean any of the small tools used by machinists , while doing machining work and 'hand tools' shall mean any of the hand tools used by fitters or carpenters or others doing hand work .
[No. 60 ( 21 ) Exp . Insp./67 . ]
A. C. BANERJEE , Jt . Secy .
PRINTED IN INDIA BY THE GENERAL MANAGER , GOVERNMENT OF INDIA PRESS , NEW DELHI AND PUBLISHED BY THE MANAGER OF PUBLICATIONS , DELHI , 1967